Flash Extractor
© Soft-Center
About     Shop     Downloads     Manual     Library     Forum     Services     Contacts
[+] Tsop48 on SSS 6132 - 98 3c 98 b3, no layout   Search  Register  Log in
This topic is locked: you cannot edit posts or make replies.
Author Message
Bolo



Joined: 05 Dec 2017
Posts: 279
Location: 506F6C616E64

PostPosted: Mon Jul 22, 2019 16:37    Post subject: [+] Tsop48 on SSS 6132 - 98 3c 98 b3, no layout
Reply with quote

Hello,

Need your help here...


  • Flash type : USB PenDrive
  • Flash chip name: Kingston 32Gb G4
  • Totall size: 32Gb
  • Banks: 1
  • ID of Bank (full 8 bit): 98 3c 98 b3 76 72 08 0e
  • Controller chip: SSS 6132 (but structure looks as TC58xxxxx)
  • Sector: 1218 (1024_4_190)
  • XOR: 9A860F (DA/SA/ECC after XOR)
  • Socket: TSOp48
  • Need to use Power Mod: 1/0x80a8


Cannot find layout

NOTES:
1) Dump readed on other reader with same parametrs becouse cannot get correct reading for this IC on NR
2) Correct Block for this case schould be 768p so I think that config need to be recreated
3) I was able to extract XOR using other tools and apply it on this case - however sine there anre no LBN on SSS i got problem with assembly (only data covered by block are recovered) - I can add to container XOR for this case but it's for 768p

Dump uploading
Bolo



Joined: 05 Dec 2017
Posts: 279
Location: 506F6C616E64

PostPosted: Mon Jul 22, 2019 22:44    Post subject:
Reply with quote

Done
Bolo



Joined: 05 Dec 2017
Posts: 279
Location: 506F6C616E64

PostPosted: Tue Aug 06, 2019 13:14    Post subject:
Reply with quote

Do we got any update here ?
Сергей



Joined: 26 Aug 2005
Posts: 17602

Flash-Extractor developer

PostPosted: Fri Aug 09, 2019 5:58    Post subject: Re: Tsop48 on SSS 6132 - 98 3c 98 b3, no layout
Reply with quote

Bolo wrote:

1) Dump readed on other reader with same parametrs becouse cannot get correct reading for this IC on NR
2) Correct Block for this case schould be 768p so I think that config need to be recreated


First need verify config

Please, read dump with original config from NR database
Upload dump or provide access with TW
Bolo



Joined: 05 Dec 2017
Posts: 279
Location: 506F6C616E64

PostPosted: Fri Aug 09, 2019 16:19    Post subject:
Reply with quote

ReUpload done
Сергей



Joined: 26 Aug 2005
Posts: 17602

Flash-Extractor developer

PostPosted: Tue Aug 13, 2019 18:47    Post subject:
Reply with quote

Load Job.txt in FE_845

There is no block numbers
We can use only Virtual Translator
But there is mix between each two blocks in image
Auto Fast will not work
Can use only Auto_Slow

Make ECC Fix
Set ECC = off
Auto_Slow

Or can try search for dirs in dump with hands and add them to Correction section of Virtual Translator. But this is hard job
Bolo



Joined: 05 Dec 2017
Posts: 279
Location: 506F6C616E64

PostPosted: Mon Aug 26, 2019 12:52    Post subject:
Reply with quote

Thank you - works perfect

Attached updated correction offsets (Job.txt) for this case if someone need - still some missing blocks which cannot find but over 90% data recovered with full structure

P.S
Attached Chip config which read +1 sector in page and then ECC back write works correct
Display posts from previous:   
This topic is locked: you cannot edit posts or make replies. All times are GMT + 4 Hours
Page 1 of 1

 

Last added
IS917   89 88 24 4b   1x4 Monolith USB 55   ec 1a a8 de   1x2 IS917   b5 64 64 54   2x1 Monolith USB 54   ad 3a 18 a3   1x1 H26M31001GMR   ad d7 94 91   1x1 Monolith USB 53   ad 3a 18 03   1x1 SM2683Lt   98 d5 84 32   1x1 PS2251-70-25   98 3a 94 93   1x1   Ref Monolith USB 52   98 3c 99 a3   1x4 PS2251-08-Q   98 3a 98 a3   1x8
News
01.12.2019 Power Adapter v3
20.04.2018 Sector Number Slow
17.03.2018 Adapter BGA-272
22.02.2018 Bad Bytes Editor
18.10.2017 Power adapter
Other products
© Soft-Center ltd.