Flash Extractor
© Soft-Center
About     Shop     Downloads     Manual     Library     Forum     Services     Contacts
Notes: Chip 45 3c 98 b3 76 71   Search  Register  Log in
Reply to topic
Author Message
jeremyb



Joined: 09 Dec 2008
Posts: 1607
Location: RecoverMyFlashDrive.com Bridgeport, CT, USA

PostPosted: Mon Jun 29, 2020 22:37    Post subject: Notes: Chip 45 3c 98 b3 76 71
Reply with quote

DDR Enablement Command:

Cmd 0x5C 0xC5 0x55
Addr 0x00
Data 0x01

Cmd 0x55
Addr 0x20
Data 0x1

Register 0x20
Value 0x00 = Disable
Value 0x01 = Enable

When DDR is Enabled the chip id changes to
45 3c 9b b3 7e f1

As stated by Arvika, this chip comes in different models/configs..

Chip Config:
// Chip
Company Toshiba
Name Monolith
ID code 98 3c 98 b3
 
// Structure
Bus 8
Banks 1 x 32 GB
Page 18336
Block 0xa12800
Blocks 0xf68
 
// Read
Cmd WL
Col 2
Row 3
DDR false
 
// Timings
RE_Up 2
RE_Down 2
 
// Special
Power
Retry
Skip_Mask_1 0xff
Skip_Page_1 0xc0
Skip_Mask_2 0xffffffff
Skip_Page_2 0xffffffff
Join CE


This chip uses Registers 0x21 0x22 and 0x24 for Read Retry, use plot to find the ideal values.

Read Retry address space is 64 values.

Register 0x21
Not sure what to make of it, it seems like it adjusts the overall sensitivity, some uncorrectable areas are corrected at the expensive of making good areas red. There is no curve Use ECC Combine..
register-0x24.png
Register 0x24 Curve
Highlighted Area = Correct Values
register-0x22.png
Register 0x22 Curve
Highlighted Area = Correct Values
jeremyb



Joined: 09 Dec 2008
Posts: 1607
Location: RecoverMyFlashDrive.com Bridgeport, CT, USA

PostPosted: Sat Nov 07, 2020 18:37    Post subject: How to Solve using Read Retry in Flash Extractor
Reply with quote

SanDisk v2 has been implemented in Flash Extractor for this generation of NAND chip. The address space is 64 (0x40) so you don't need to scan the entire range with tune or plot. Also because the address space is so narrow its difficult to read with plot.

Reg 2 is the major register, 1, and 0 are minor.

The easier method to solve Read Retry is below.

1. Find the Layout
2. Launch Read Retry mode
3. Under Properties

Retry = Sandisk v2 / 00 00 00
Ignore Busy = True


4. Under Tune
Regs = 2,1,0
Delta = 32
Repeat = 1


and let it run Smile
Properties-Window.PNG
Tune-Window.PNG
Plot-Window.PNG
Сергей



Joined: 26 Aug 2005
Posts: 18168

Flash-Extractor developer

PostPosted: Sat Nov 07, 2020 18:49    Post subject:
Reply with quote

Sandisk v2 is not ready, i think

I need some more chips to test it

Some combinations of register values change non-DDR to DDR

So need adjust registers
jeremyb



Joined: 09 Dec 2008
Posts: 1607
Location: RecoverMyFlashDrive.com Bridgeport, CT, USA

PostPosted: Sat Nov 07, 2020 22:19    Post subject:
Reply with quote

Сергей wrote:
Sandisk v2 is not ready, i think

I need some more chips to test it

Some combinations of register values change non-DDR to DDR

So need adjust registers


I don't think that is the case..

See my notes..
This chip uses Registers 0x21 0x22 and 0x24 for Read Retry.

Register 0x20 = Enable DDR Mode
if
Register 0x20 = Enable - Retry Regs still work
Register 0x20 = Disable - Retry Regs still work

Register 0x20 isn't used by Read Retry in SanDisk v2 Smile

Almost all NAND chips have DDR enablement commands that change non-DDR into DDR, you just need to modify a register value, so I don't know what you're inferring..
jeremyb



Joined: 09 Dec 2008
Posts: 1607
Location: RecoverMyFlashDrive.com Bridgeport, CT, USA

PostPosted: Sun Nov 08, 2020 19:58    Post subject:
Reply with quote

Here's a video showing it work....

https://youtu.be/5bxg5O4EdcU

Very Happy Very Happy Very Happy
Display posts from previous:   
Reply to topic All times are GMT + 4 Hours
Page 1 of 1

 

Last added
SM2246XT   89 84 64 3c   2x4   v2 IS903   45 3a 94 93   2x1 MK670H   98 3c 95 93   2x4 82-00515-5   45 3c a9 a2   1x2 UT163-T6   ec d5 55 25   2x2 AU6384   ec da 80 15   1x1 AU6983   2c d5 94 3e   4x1 AU6980   ec d3 55 25   1x1 AU6980   ad dc 80 95   1x2 AU6980 B4   ad dc 80 95   1x1
News
21.07.2020 RR manual updated
10.07.2020 Power adapter in stock
05.05.2020 RR even and odd blocks
10.03.2020 RR for ad 3a 18 03
01.12.2019 Power Adapter v3
Other products
© Soft-Center ltd.