Flash Extractor
© Soft-Center
About     Shop     Downloads     Manual     Library     Forum     Services     Contacts
[+] COB 1x2 (ec de 98 de) Check please   Search  Register  Log in
This topic is locked: you cannot edit posts or make replies.
Author Message
datasave



Joined: 17 Nov 2017
Posts: 248
Location: South Korea

PostPosted: Wed Jun 19, 2019 11:31    Post subject: [+] COB 1x2 (ec de 98 de) Check please
Reply with quote

The photo is in the container.
The layout is SM ?? 1148.
However, there is a red area in the staircase.
Please check.
datasave



Joined: 17 Nov 2017
Posts: 248
Location: South Korea

PostPosted: Wed Jun 19, 2019 13:28    Post subject:
Reply with quote

Uploaded
Сергей



Joined: 26 Aug 2005
Posts: 17172

Flash-Extractor developer

PostPosted: Wed Jun 19, 2019 20:17    Post subject:
Reply with quote

Layout "SM3257_41 1148_27 Xor b36e_256"

Need make ECC map 100% green

Try Test Retry
http://www.flash-extractor.com/manual/read_retry/
datasave



Joined: 17 Nov 2017
Posts: 248
Location: South Korea

PostPosted: Thu Jun 20, 2019 4:50    Post subject:
Reply with quote

I know. However, the results do not change to green after 'Test retry'. Sad Sad
Сергей



Joined: 26 Aug 2005
Posts: 17172

Flash-Extractor developer

PostPosted: Thu Jun 20, 2019 9:58    Post subject:
Reply with quote

Can try change voltage from 3.3v to 2.4v with 0.1v step
(change only when reader is disconnected)

But usually it not help

And i'm not sure that it will work with monolith
datasave



Joined: 17 Nov 2017
Posts: 248
Location: South Korea

PostPosted: Thu Jun 20, 2019 13:25    Post subject:
Reply with quote

Thank you for your advice.
datasave



Joined: 17 Nov 2017
Posts: 248
Location: South Korea

PostPosted: Fri Jun 21, 2019 10:00    Post subject:
Reply with quote

I made a dump again. Thank you for your check.
Dump file uploaded.
datasave



Joined: 17 Nov 2017
Posts: 248
Location: South Korea

PostPosted: Fri Jun 28, 2019 4:59    Post subject:
Reply with quote

Any other issues?
Сергей



Joined: 26 Aug 2005
Posts: 17172

Flash-Extractor developer

PostPosted: Fri Jun 28, 2019 23:29    Post subject:
Reply with quote

Many blocks have ff in SA

Virtual Translator give better result then Block Number assembler

But ECC map have red sectors
Сергей



Joined: 26 Aug 2005
Posts: 17172

Flash-Extractor developer

PostPosted: Fri Jun 28, 2019 23:31    Post subject:
Reply with quote

But there is an "Gy5" files

VT will not find them

So better use combination of VT + BN
Job.txt attached
datasave



Joined: 17 Nov 2017
Posts: 248
Location: South Korea

PostPosted: Mon Jul 01, 2019 6:10    Post subject:
Reply with quote

Сергей wrote:
But there is an "Gy5" files

VT will not find them

So better use combination of VT + BN
Job.txt attached


The result of this case is good. Thank you very much.
Display posts from previous:   
This topic is locked: you cannot edit posts or make replies. All times are GMT + 4 Hours
Page 1 of 1

 

Last added
IS917   45 3e 97 93   1x1 SM3268P-AB   98 de 88 a3   1x1 SM2246XT H AA   2c a4 64 32   4x4 Monolith Micro SD 2   98 d7 99 b2   1x1 SM3268P-AB   45 3c 98 b3   2x1 Monolith Micro SD_1   98 d7 99 b2   1x2 PS2251-68-5   98 de 94 93   2x1 SM3257Q AA   ec d7 98 ca   2x2 SM3267L-AB   98 d7 98 92   1x1 Monolith Micro SD PS 1146   98 3a 98 b3   1x1
News
20.04.2018 Sector Number Slow
17.03.2018 Adapter BGA-272
22.02.2018 Bad Bytes Editor
18.10.2017 Power adapter
07.10.2016 Conatiner v9
Other products
© Soft-Center ltd.